PZRacing DesmoTronic DE700 adds 50Hz GPS lap timing through the original dashboard. Includes Wi-Fi, racing-line and speed logging and RacePro analysis. Check the model-specific application list.

PZRacing A2-Tronic AP701 adds 50Hz GPS lap timing through the original dashboard. Includes Wi-Fi, racing-line and speed logging and RacePro analysis. Check the model-specific application list.

The PZRacing BM500S is a mounting bracket for a compatible Start lap timer on a top yoke with a drilled centre nut. It fits holes from 12 to 18 mm and positions the lap timer centrally in the cockpit.

The PZRacing BM200S is a mounting bracket for a compatible Start lap timer on a top yoke with a drilled centre nut. It fits holes from 12 to 18 mm and positions the lap timer centrally in the cockpit.

The PZRacing SSBTB050 is a 50 cm extension cable with 5-pin M8 connectors, male to female. This version is intended for the connection between a suitable Start instrument and Box Expander.

The PZRacing SSM100F is a 100 cm extension cable with 4-pin M8 connectors, male to female. This version extends a compatible four-pin sensor connection. Length: 100 cm.

The PZRacing SSIT100 is an infrared sensor for wheel or tyre temperature measurement. It adds temperature information to a suitable measurement system without placing a contact probe against the rotating surface.

The PZRacing SSLS200 is the separate lambda 4.9 sensor from the KITLS200 measurement kit. It is intended for the matching RRLS201 interface and a suitable system for recording lambda data.

The PZRacing KITLS200 combines the SSLS200 lambda 4.9 sensor and RRLS201 signal interface. The kit adds a lambda measurement channel to a suitable measurement or data-logging installation.

The PZRacing SSLP075 is a linear potentiometer for recording suspension movement. Maximum travel is 75 mm. With a suitable data logger, suspension movement can be recorded as a separate measurement channel.

The PZRacing SSLP150 is a linear potentiometer for recording suspension movement. Maximum travel is 150 mm. With a suitable data logger, suspension movement can be recorded as a separate measurement channel.

The PZRacing SSEK100 is an M5-threaded K-type thermocouple for measuring exhaust gas temperature. It is the separate sensing element from the KITEK100 kit and is used with a suitable thermocouple interface.

The PZRacing KITEK100 records exhaust gas temperature with a suitable data logger. The kit contains an SSEK100 K-type thermocouple with M5 thread and the matching RREK101 signal interface.

The PZRacing RRBK02 is the mounting kit with a 1/8-inch connection for brake-pressure measurement. It is the mounting component offered with the SSPS069 pressure sensor in the KITBK02 kit.

The PZRacing SSY150 is a Y-cable for connecting two temperature channels simultaneously to the Start Plus ST400-P: one NTC sensor and one thermocouple. It is 150 cm long and specifically intended for this dashboard.

The PZRacing SSIS100 is an inductive speed sensor for a suitable data-logging or instrument setup. It provides a separate speed-signal source and is supplied with a mounting bracket.

The PZRacing SSCTSR100 is a signal cable for acquiring speed, throttle position, gear or rpm from the ECU. It connects the selected vehicle signal to a suitable measurement system.

The PZRacing SSRPM100 picks up engine rpm inductively from the spark-plug lead. It provides an rpm source for a suitable PZRacing measurement system where the ignition signal can be obtained in this way.

The PZRacing BCAN-TM01 reads vehicle parameters from the ECU over CAN bus. This version is intended for the listed TM 250 and TM 450 models and supplies available vehicle data to a suitable PZRacing measurement system.

The PZRacing BOX2-MINI is an expansion module for acquiring ECU signals on road motorcycles. It supports rpm, speed, throttle position and calculated gear, with an input for a temperature sensor.

PZRacing Start Basic ST500-B is a 50Hz GPS lap timer with colour touchscreen, automatic circuit recognition and up to three splits. View lap times, ideal time and predicted time on the instrument.

The PZRacing GT102 is an rpm interface for GearTronic GT3000 and GT400. It is intended for vehicles whose original engine-speed signal is not directly compatible with the gear indicator.

The PZRacing OBD100 extracts signals from a suitable car’s diagnostic connector for accessories including GearTronic GT3000, GT400 and LighTronic LT2000. It provides power, ground, rpm, speed and an adjustable temperature-alarm output.

The PZRacing GearTronic² GT400 combines a digital gear display with an adjustable shift light. The LCD shows the selected gear, while five rpm levels can be configured for the shift indication.